AutoZone does check ABS lights as well as check engine lights.
AutoZone can check your ABS light and check for codes but AutoZone cannot fix the ABS light or turn it off.
The most common cause of the ABS light to come on is a bad or faulty ABS module, broken wheel speed sensors, the ABS system being turned off or low brake fluid.
ABS lights will throw a code although the codes can vary from vehicle to vehicle as there are 40 different ABS fault codes and also 80 + pages of diagnostic procedures.
Around 1/2 of the fault codes with ABS lights and the diagnostic procedures involve the 4 wheel sensors and the connections.
The wheel sensors should read between 800 to 1400 ohms when they are tested with an ohm meter.
Rain can cause ABS light to come on or when driving through water when the water causes wires going to the ABS sensor to get wet and short out.
Road gunk could also get stuck on the ABS sensor and cause the sensor to not read.
Another cause is that the wheels were hot and you drove through a puddle of water that caused the ABS sensor ring to crack.
The problems that ABS can cause are loss of traction under heavy braking, hydroplaning, and skidding and loss of control.
You can tell which ABS sensor is bad by checking the resistance across the signal and the ground leads which generally should read 800 to 2000 ohms which is a good reading if it reads steady in this range and indicates the ABS sensor is good.
If the resistance reading constantly changes or increases on the ohm meter then the ABS sensor is faulty.
An ABS light does not mean brake failure if the ABS light is the only light that is on and not also the red brake light.
If the red brake light is on along with the ABS light then it means brake failure or a problem with the brakes.
The ABS light being on by itself means there's an issue with the ABS system.
The most common cause of the ABS light to come on is a malfunctioning or bad ABS module or faulty wheel speed sensor.
An ABS light is not very serious if only the ABS light is on.
However if both the ABS light and the brake light are on at the same time then it's more serious and means the vehicle is not safe to drive unless you get the issue fixed.
The ABS system helps with stopping distances and vehicle control and is an important safety feature that should be fixed and maintained.
A car can work without an ABS sensor although the cars stability and stopping properly in difficult conditions will be affected.
ABS sensors are an important part of the vehicle to keep the vehicle stable and allow for stopping properly in emergencies.
An ABS light should be yellow in color and will usually have ABS written underneath it or inside the light.
When the ABS light is on it means that there is an issue with the ABS system that should be addressed soon to ensure safe driving of the vehicle.
Removing the ABS fuse will not turn off the ABS light as the ABS fuse is for the ABS system itself and not the ABS light.
The ABS light will still remain on with the ABS fuse removed but the ABS system will not work.
The ABS sensor is located in each wheel hub or rotor on a 4 channel ABS system.
Your ABS sensor can also be mounted or located in the rear differential in certain rear wheel drive vehicles.
ABS can shut off a car when it detects that one wheel starts to spin irregularly then it will cut the engine off until it establishes traction.
The ABS cutting off power to the engine is designed to prevent skidding out of control by accidentally applying too much power.
When your ABS light is on but your brakes are fine the most common reason for the ABS light being on but brakes are good is a bad or malfunctioning ABS wheel speed sensor.
Other causes of the ABS light being on are low brake fluid, faulty bulb check, worn hydraulic pump or bad ABS module.
The four reasons your ABS light is on include a malfunctioning ABS module, low levels of brake fluid in the brake fluid reservoir, broken wheel speed sensors, or the system is turned off.
If you ignore the ABS light it could cause the ABS system to completely malfunction and make cause the tires to get locked under heavy braking which limits the vehicles maneuverability in emergencies when you need to stop.
The most common cause of the ABS light to come on is a malfunctioning ABS module or even low levels of brake fluid and bad wheel speed sensors.
ABS light being on can mean you need new brake pads or it could mean you're low on brake fluid or something else is wrong with your ABS system.
When the ABS light comes on it's a sign that something is wrong with the ABS system which could also be a bad wheel sensor.
Worn brake pads can cause the ABS light to come on as worn brake pads can make the fluid in the brake reservoir seem lower which can trigger the ABS light and even the brake light.
If your ABS light comes on it's best to check the brake pads and the brake fluid levels first and if that does not fix the issue then you have something wrong with the ABS system or even a wheel speed sensor could be bad.
Bad wheel speed sensors can also cause the ABS light to come on.
It is OK to drive with the ABS light on.
Even when the ABS light is on your brakes on your vehicle are still working as usual and you'll be able to stop the vehicle..
However when you drive with the ABS light on the vehicle's tires are at a risk of getting locked under heavy braking which limits your ability to maneuver properly in emergencies.
The ABS light should be taken seriously though and be checked out because it's a sign that the ABS system needs checked out and the ABS system could be malfunctioning.
The most common reasons that typically cause the ABS light to turn on include a malfunctioning ABS module, low levels of brake fluid in the brake fluid reservoir, broken wheel speed sensors, or the system is turned off.
The vehicles ABS actually shares some important components with another system in your vehicle: your traction control system.
The ABS light is yellow for a reason – it indicates that caution should be taken while driving the vehicle, but there is no imminent need to stop.
It is wise to get the system checked out sooner than later.
Worn brake pads deplete your brake fluid.
By doing this, they can trigger your car's ABS light.
Anti-lock brake systems, or ABS, are an essential safety feature for any car. When the system is damaged or needs a part to replace, it can cost anywhere from $320.00 to $1,000.00
The exact cost really depends on your car and the components of its given ABS system.
Firstly, you should check your brake fluid reservoir to ensure that the levels aren't too low, as the ABS warning light can be activated if the levels of brake fluid have dropped.
If this is clearly an issue, you can top the brake fluid up yourself, which should cause the ABS light to go off.
When a car's ABS starts to fail, the brake pedal may gradually stop working.
As this happens, you'll need to increasingly press down harder on the brake pedal over time to get your car to stop.
Eventually, you won't be able to press down on your brake pedal to safely stop your car, which means your ABS no longer works.
If the TCS and the ABS warning lights both come on, along with the red main brake warning light, you should not drive the car until the problem has been fixed.